Manuel d'utilisation / d'entretien du produit IM736-D du fabricant Lincoln Electric
Aller à la page of 48
PO WER MIG ™ 300 OPERA TOR’S MANUAL IM736-D February, 2004 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
4 FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv Mar. ‘93 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
v v Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page ________________________________________________________________________ Installation ................................................................................................................... ....Section A Technical Specifications .
A-1 A-1 INST ALLA TION Input Voltage/ 230Amps @ 300Amps @ 75°C Copper Wire Fuse Frequency (Hz) 29 Volts 32 Volts AWG (IEC) or (100% Duty Cycle) (60% Duty Cycle) Sizes (MM 2 ) Breaker Size 208/60* 48 A 72 A 6 (16 mm 2 ) 90 A 230/60 43 A 62 A 6 (16 mm 2 ) 80 A 460/60 22 A 31 A 10 (6 mm 2 ) 50 A 575/60 17 A 25 A 12 (2.
A-2 A-2 INST ALLA TION ONL Y QUALIFIED PERSONNEL SHOULD INST ALL, USE OR SERVICE THIS EQUIP- MENT . UNCRA TING THE POWER MIG 300 Cut banding and lift off cardboard carton. Cut banding holding the machine to the skid. Remove foam and corrugated packing material.
A-3 A-3 INST ALLA TION FIGURE A.2 — Receptacle Diagram CONNECT TO A SYSTEM GROUNDING WIRE. SEE THE UNITED STATES NATIONAL ELECTRICAL CODE AND/OR LOCAL CODES FOR OTHER DETAILS AND MEANS FOR PROPER GROUNDING. CONNECT TO HOT WIRES OF A THREE-WIRE, SINGLE PHASE SYSTEM OR TO ONE PHASE OF A TWO OR THREE PHASE SYSTEM.
A-4 GUN AND CABLE INST ALLA TION A Magnum 300 gun and 15Ft.(4.6m) cable (12Ft.(3.7m) for Codes 11000 and below) are provid- ed with the POWER MIG 300. A Magnum cable liner for .035-.045" (0.9-1.2 mm) electrode and contact tips for .035” (0.9mm) and .
A-5 A-5 INST ALLA TION DO NOT ATTACH THE REGULATOR IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier of this condition. Oil or grease in the presence of high pressure oxygen is explosive. 3. Stand to one side away from the outlet and open the cylinder valve for an instant.
B-1 B-1 OPERA TION COMMON WELDING ABBREVIA- TIONS WFS • Wire Feed Speed CC • Constant Current CV • Constant Voltage GMAW (MIG) • Gas Metal Arc welding GMAW-P (MIG) • Gas Metal Arc welding-(P.
B-2 B-2 OPERA TION POWER MIG 300 PRODUCT DESCRIPTION The POWER MIG 300 is a complete semiautomatic multi-process DC arc welding machine offering CV and CC DC welding.
5. MULTI-PROCESS PANEL - This panel enables selection of weld modes as well as adjustment of certain weld parameters within each weld mode. The eight discrete LED ’ s are used to identify which selec- tion will be shown on the display.
B-4 B-4 OPERA TION POWER MIG 300 SETTING AND CONFIGURING THE POWER MIG 300 FOR WELDING • Check that the electrode polarity is correct for the process and turn the Power Switch to the "ON" position.
B-5 B-5 OPERA TION POWER MIG 300 MUL TI-PROCESS P ANEL FUNCTIONS Weld Mode Setting the Weld Mode is selecting the proper program from the ones available in the machine ’ s memory for a particular welding application. The table on the right side of the front panel (See Figure B.
B-6 B-6 OPERA TION POWER MIG 300 Arc Control (See Table B.2) There are no specific unit values offered because the setting of this feature largely depends upon operator preference. Arc Control has a different effect on the character of the arc depending upon the welding process applied.
B-7 B-7 OPERA TION POWER MIG 300 In the case of special waveforms designed for pulsed weld- ing aluminum, Pulse on Pulse ™ , the effect is similar to what occurs with standard pulse. As the Arc Control is increased from +1 to +10 the frequency of the Pulse on Pulse array increases.
B-8 B-8 OPERA TION POWER MIG 300 5. Rotate the spindle and adapter so the retaining spring is at the 12 o'clock position. 6. Position the Readi-Reel so that it will rotate in a direc- tion when feeding so as to be de-reeled from top the of the coil.
B-9 B-9 OPERA TION POWER MIG 300 4. Re-install the Retaining Collar. Make sure that the Release Bar “ pops up ” and that the collar retainers fully engage the retaining ring groove on the spin- dle.
B-10 B-10 OPERA TION POWER MIG 300 SPECIAL WELDING PROCESSES A V AILABLE ON THE POWER MIG 300 PULSE WELDING (GMA W-P) The pulsed-arc process is, by definition, a spray trans- fer process wherein spray transfer occurs in pulses at regularly spaced intervals.
B-1 1 B-1 1 OPERA TION POWER MIG 300 PULSE-ON-PULSE ™ (GMA W-PP) Pulse on Pulse ™ is a Lincoln process specifically designed for use in welding relatively thin (less than 1/4" thick) aluminum (See Table B.3). It gives weld beads with very consistent uniform ripple.
B-12 B-12 OPERA TION POWER MIG 300 POWER MODE ™ The Power Mode ™ process was developed by Lincoln to maintain a stable and smooth arc at low procedure settings which are needed to weld thin metal without pop-outs or burning-through. For Aluminum welding, it provides excellent control and the ability to maintain constant arc length.
C-1 C-1 ACCESSORIES DRIVE ROLL KITS Refer to Table C.1 for various drive roll kits that are available for the POWER MIG. All items in Bold are supplied standard with the POWER MIG. TABLE C.1 * .035 Aluminum recommended for Push-Pull systems only. 3/64" (1.
C-2 C-2 ACCESSORIES Non-Synergic Weld Modes (Mode 5) • Voltage is adjustable at the power source. The right control knob on the power source will adjust the voltage that is displayed in the meter directly above it.
D-1 D-1 MAINTENANCE CONT ACT TIP AND GAS NOZZLE INST ALLA TION a. Choose the correct size contact tip for the elec- trode being used (wire size is stenciled on the side of the contact tip) and screw it snugly into the gas diffuser. b. Be sure the nozzle insulator is fully screwed onto the gun tube and does not block the gas holes in the diffuser.
D-2 D-2 MAINTENANCE 5. Seat Liner bushing into back of gun. Secure Liner by tightening set screw. Do not install the gas dif- fuser at this time. 6 . Lay the cable straight and trim Liner to 9/16 ” . Remove burrs. 7. Secure the gas diffuser into the tube.
E-1 E-1 TROUBLESHOOTING If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
POWER MIG 300 E-3 E-3 TROUBLESHOOTING Observe Safety Guideline detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) Output voltage and wire feed is pre- sent when gun trigger is not pulled (not activated). Machine output is low. Welds are “ cold ” , weld bead is rounded or bumped up demonstrating poor wet- ting into plate.
POWER MIG 300 E-4 E-4 TROUBLESHOOTING Observe Safety Guidelines detailed in the beginning of this manual. If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your LOCAL AUTHORIZED LINCOLN ELECTRIC FIELD SERVICE FACILITY for assistance before you proceed.
POWER MIG 300 E-5 E-5 TROUBLESHOOTING PROBLEMS (SYMPTOMS) Gas does not flow when gun trigger is pulled. POSSIBLE AREAS OF MISADJUSTMENT(S) 1. Make sure gas supply is con- nected properly and turned “ on ” . 2. If the gas solenoid does actuate (click) when the gun trigger is pulled there may be a restriction in the gas supply line.
E-6 TROUBLESHOOTING E-6 POWER MIG 300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-7 TROUBLESHOOTING E-7 POWER MIG 300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-8 TROUBLESHOOTING E-8 POWER MIG 300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-9 TROUBLESHOOTING E-9 POWER MIG 300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-10 TROUBLESHOOTING E-10 POWER MIG 300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
POWER MIG 300 F-1 F-1 WIRING DIAGRAMS NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-2 F-2 WIRING DIAGRAMS NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-3 F-3 WIRING DIAGRAMS NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-4 F-4 WIRING DIAGRAM POWER MIG 300 WIRI NG DIAGRAM POWER MIG 30 0 (FOR CODES 11097, 11098) J4 1 2 3 4 5 6 7 8 9 10 11 12 J3 1 2 3 4 5 6 7 8 9 10 J7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 J 9 1 2 3 4.
DIMENSION PRINT F-5 POWER MIG 300 F-5 3-00F M19231.
NOTES POWER MIG 300.
NOTES POWER MIG 300.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIPAMENTO E AS P AR TES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lincoln Electric IM736-D c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lincoln Electric IM736-D - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lincoln Electric IM736-D, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lincoln Electric IM736-D va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lincoln Electric IM736-D, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lincoln Electric IM736-D.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lincoln Electric IM736-D. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lincoln Electric IM736-D ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
